Home » News » Industry News » S32750 vs Duplex 2205: Key Differences, PREN and How to Choose

S32750 vs Duplex 2205: Key Differences, PREN and How to Choose

Views: 4     Author: Monica     Publish Time: 2026-11-02      Origin: Site

twitter sharing button
wechat sharing button
whatsapp sharing button
linkedin sharing button
pinterest sharing button
facebook sharing button
sharethis sharing button

A specification-level comparison of super duplex S32750 (2507) and standard duplex 2205: designations, chemistry, PREN, strength, corrosion limits, weldability, sour-service rules and cost — with a purchase-order checklist.

S32750 vs Duplex 2205.webp

Key Facts About S32750 vs Duplex 2205

One-line difference

S32750 (super duplex 2507) raises Cr, Mo and N above Duplex 2205 levels: typical PREN about 42 to 43 versus about 35 to 36, and minimum yield 550 MPa versus 450 MPa.

Designations

2205 = UNS S31803 or S32205 (EN 1.4462), ASTM A182 F51 or F60. 2507 = UNS S32750 (EN 1.4410), ASTM A182 F53. The forging grade on the certificate is the fastest way to tell them apart.

Strength

Proof 550 vs 450 MPa; tensile 795 vs 620 MPa; elongation 15% vs 25%. At equal hoop stress, 2507 needs about 18% less wall than 2205.

Corrosion

Typical ASTM G48 critical pitting temperature is about 50 °C or higher for 2507 versus about 35 °C for 2205; crevice and chloride-SCC margins move the same direction.

Temperature window

Both grades: about minus 46 °C (with impact tests) to about 250 to 300 °C continuous. 475 °C embrittlement and sigma phase above 600 °C govern both.

Welding

ER2209 for 2205, ER2594 for 2507; low heat input, interpass cap, argon purge 25 to 50 ppm O2, no PWHT. 2507 has the narrower window.

Sour service

Both can be NACE MR0175 / ISO 15156-3 qualified; commonly 28 HRC max for 2205 and 32 HRC max for 2507, edition-dependent.

Cost

2507 typically carries a 25 to 50% material premium over 2205; it pays back only when the service, wall thickness or lifecycle risk justifies it.

Cluster position

This is the specification-level comparison spoke in the Super Duplex S32750 cluster; the hub page is the S32750 guide, and the application-focused sibling is the 2205 vs 2507 'when to use which' article.

S32750 (super duplex 2507) and Duplex 2205 belong to the same family of roughly 50/50 austenite-ferrite steels, but 2507 pushes chromium, molybdenum and nitrogen higher — typical PREN about 42 to 43 versus about 35 to 36 — and lifts minimum yield strength from 450 to 550 MPa.

Specify 2205 when the service sits inside its corrosion envelope and the fabrication window matters most; specify S32750 when hotter, more concentrated chloride duty, higher design stress or a sour-service qualification drives the decision.

What Is the Real Difference Between S32750 and Duplex 2205?

The real difference is three alloying elements and one screening number. S32750 raises chromium to 24.0–26.0%, molybdenum to 3.0–5.0% and nitrogen to 0.24–0.32%, which lifts the typical pitting resistance equivalent number (PREN) from about 35 to about 42–43, and it adds about 100 MPa of minimum yield strength. Every other distinction between the grades — pitting temperature, crevice margin, sour-service envelope, weld window, price — follows from that chemistry step.

Both grades are duplex stainless steels: roughly half austenite, half ferrite, which is where the high strength and the chloride stress-corrosion resistance come from. Duplex 2205 is the 22% chromium workhorse of the family and the default choice for seawater, chemical and marine duty. S32750 is the 25% chromium super duplex grade, engineered for the same duties at higher temperature, higher chloride concentration or higher stress. The step from 2205 to 2507 is the same kind of jump as from 316L to 2205, but smaller in relative terms — and it comes with a narrower processing window, because the higher alloy content that buys the corrosion margin also makes the steel more sensitive to heat input, interpass temperature and quench delay.

Short answer for citation: S32750 (UNS S32750, EN 1.4410, ASTM A182 F53) is the 25Cr super duplex grade; Duplex 2205 (UNS S31803/S32205, EN 1.4462, ASTM A182 F51/F60) is the 22Cr standard duplex grade. The difference is PREN (about 42 versus about 35), minimum yield strength (550 versus 450 MPa) and fabrication window (2507 is narrower).

How Do You Tell the Two Grades Apart on Paper?

Before comparing any property, confirm which grade is actually on the certificate — by UNS number, EN number and ASTM A182 forging grade, never by the loose trade name "duplex". The designation decoder below is the fastest way to separate 2205 from 2507 on a mill test certificate.

Table 1. Designation decoder: Duplex 2205 versus super duplex S32750

Designation system

Duplex 2205

Super duplex S32750 (2507)

Common name

Duplex 2205

Super duplex 2507

UNS number

S31803 (older) or S32205 (current)

S32750

EN 10088 designation

1.4462, X2CrNiMoN22-5-3

1.4410, X2CrNiMoN25-7-4

GB (China) designation

022Cr22Ni5Mo3N

022Cr25Ni7Mo4N

ASTM A182 forging grade

F51 (S31803) or F60 (S32205)

F53

ASTM A995 casting grade

4A (CD3MN)

5A (CE3MN)

Mill trademarks

SAF 2205 and equivalents

SAF 2507, UR 52N+, Avesta 2507

Typical PREN band

34 to 38

40 to 43

Two traps are worth naming.

First, F51 and F60 are both 2205, but F51 permits nitrogen as low as 0.08%, which pulls the guaranteed PREN floor down to about 31–32, while F60 guarantees 0.14% minimum and a floor of about 34; most modern orders should say F60/S32205 unless the design already accounts for F51 chemistry, and dual-certified S31803/S32205 material is common. S

econd, a purchase order that says only "duplex" or only "F51" does not distinguish 2205 from 2304 or 2507 — always write the UNS number. The full decoding logic is explained in the duplex numbering system guide.

What Does Each Alloying Difference Buy You?

The composition table below is the specification-level view: both grades side by side under the same ASTM A240 chemistry limits, with the engineering consequence of each difference spelled out.

What Does Each Alloying Difference Buy You.webp

Table 2. Composition comparison per ASTM A240 (wt %)

Element

Duplex 2205 (S32205)

Super duplex S32750

What the difference buys

Chromium

22.0 to 23.0

24.0 to 26.0

A stronger passive film; the backbone of pitting resistance

Nickel

4.5 to 6.5

6.0 to 8.0

Austenite stability, toughness and formability

Molybdenum

3.0 to 3.5

3.0 to 5.0

Crevice corrosion resistance and resistance to reducing acids

Nitrogen

0.14 to 0.20

0.24 to 0.32

Strength and austenite stability, plus a very large PREN contribution (16 times its weight percentage)

Copper

Not specified

0.50 max — a ceiling, not a required range

No required copper in S32750; copper is a required addition only in S32760

Tungsten

Not specified

Not specified

Tungsten appears only in S32760 (0.50 to 1.00), never in S32750

Carbon

0.030 max

0.030 max

Both kept low to protect weldability; sensitisation is not the duplex concern that it is for ferritic grades

Iron

Balance

Balance

The matrix that holds everything together

Read the table as a cause-and-effect chain. Chromium and molybdenum raise the pitting and crevice ceilings; nitrogen does the same while also adding strength and stabilising the austenite half of the structure — which is why its coefficient in the PREN formula is 16.

The penalty is metallurgical, not chemical: the same alloy content that resists chlorides also accelerates sigma-phase precipitation, so the mill's annealing and quenching discipline matters more for 2507 than for 2205. The element-by-element detail for the super duplex grade is on the S32750 chemical composition page.

How Much Stronger Is S32750, and What Does the Extra Strength Buy?

S32750's minimum 0.2% proof strength is 550 MPa against 450 MPa for 2205, and its minimum tensile is 795 MPa against 620 MPa — roughly 22% more yield — while minimum elongation falls from 25% to 15%. The strength premium is a wall-thickness and weight argument, not a stiffness argument, and it should never be the only reason to specify the higher grade.

Table 3. Minimum room-temperature mechanical properties by product standard

Requirement

Grade

A240 plate

A790 pipe

A276 bar

A182 forging

0.2% proof, MPa (ksi)

2205 (S32205)

450 (65)

450 (65)

450 (65)

450 (65)

0.2% proof, MPa (ksi)

S32750

550 (80)

550 (80)

550 (80)

550 (80)

Tensile, MPa (ksi)

2205 (S32205)

620 (90)

620 (90)

620 (90)

620 (90)

Tensile, MPa (ksi)

S32750

795 (116)

795 (116)

795 (116)

795 (116)

Elongation, min %

2205 / S32750

25 / 15

25 / 15

25 / 15

25 / 15

Hardness, max

2205 / S32750

31 HRC / 32 HRC

31 HRC / 32 HRC

31 HRC / 32 HRC

31 HRC / 32 HRC

At equal hoop stress the relative wall factor is about 0.31 for S32750, about 0.38 for 2205 and 1.00 for 316L — so 2507 needs roughly 18% less wall than 2205 for the same pressure duty, and that saving compounds into less weld metal, lower weight and easier handling.

One caution: the elastic modulus is not higher (about 196 to 200 GPa for both), so deflection, buckling and flange-tightness checks do not improve when you buy the stronger grade. Wall-thickness tables for sizing are on the ASME B36.19M dimension page, and the full property set is on the S32750 mechanical properties page.

Key point: Do not buy the upgrade for strength alone. If 2205 meets the pressure design at an acceptable wall, only the corrosion margin can justify the S32750 premium — and that margin should be demonstrated from the service conditions, not from the datasheet.

What Is PREN, and How Do You Calculate It from the Specification?

PREN = %Cr + 3.3×%Mo + 16×%N. It is a screening index, not a design allowable — but it is the most useful single number for comparing these two grades, and it can be calculated directly from the ASTM A240 composition ranges without any proprietary data.

Table 4. PREN derived from the ASTM A240 specification ranges

Grade

PREN from specification minima

PREN at mid-range

How to read it

2205 (S32205)

22.0 + 3.3×3.0 + 16×0.14 = 34.1

22.5 + 3.3×3.25 + 16×0.17 = 35.9

Guaranteed floor about 34; typical heats 35 to 38

S32750

24.0 + 3.3×3.0 + 16×0.24 = 37.7

25.0 + 3.3×4.0 + 16×0.28 = 42.7

Floor about 38 from minima; typical heats 42 to 43

First, always calculate PREN from the actual heat chemistry on the mill certificate, not from nominal composition: a super duplex heat sitting at the analytical low end of molybdenum and nitrogen can calculate below 41 even while it is inside the specification range, which is why offshore specifications such as NORSOK M-630 require PREN of 41 or more from the actual OES analysis. Second, remember what PREN does not say: it says nothing about crevice geometry, deposits, flow, temperature or the weld — and those are what actually govern service life.

Which Grade Resists Pitting and Crevice Corrosion Better?

S32750, by a clear and measurable margin. In the standard ASTM G48 ferric chloride test the critical pitting temperature of 2507 sits at about 50 °C or higher, against about 35 °C for 2205 — roughly a 15 °C shift in the temperature at which the passive film starts to break down in chlorides, and crevice resistance moves in the same direction.

Which Grade Resists Pitting and Crevice Corrosion Better.webp

Table 5. Corrosion performance bands (typical producer values)

Property

Duplex 2205

Super duplex S32750

Note

Typical PREN

34 to 38

40 to 43

Screening index calculated from heat chemistry

Critical pitting temperature (ASTM G48)

about 35 °C

about 50 °C or higher

Method-dependent; Method E is commonly quoted for 2507

Critical crevice temperature

below its CPT

about 35 °C or higher

Governs gaskets, washers, deposits and stagnant zones

Chloride SCC ceiling (indicative)

about 100 °C

about 130 °C

Depends on chloride level, pH and applied stress

Seawater verdict

Fully capable

Preferred for hot or concentrated brine

High-pressure desalination sections favour 2507

Treat the G48 numbers as typical producer values, not specification minima: results depend on the test method (Method A in 6% ferric chloride versus Method E), the section thickness and the heat treatment.

What is standardised is the screen for bad processing: ASTM A923 (Methods A and C corrosion, Method B impact) detects the detrimental intermetallic phase that a poor solution anneal leaves behind, and it is the test that separates a correctly processed super duplex heat from one that will pit in service. The weld and heat-affected zone are usually the weak link in either grade — not the base metal. More detail is on the S32750 corrosion resistance page.

Can Both Grades Resist Chloride Stress Corrosion Cracking?

Yes — that is what the duplex structure is for. Both grades resist chloride stress-corrosion cracking at temperatures where 316L cracks, and S32750 extends the practical ceiling, indicatively from about 100 °C to about 130 °C in neutral chloride service, while tolerating higher chloride concentrations.

Neither grade is immune, though: the risk is driven by the combination of chloride concentration, temperature, pH and tensile stress, and it concentrates at crevices, deposits and stagnant zones. Where the service is hot, concentrated or stagnant seawater, the 2507 margin is the safer specification; the desalination guide and the seawater piping selection guide walk through the application-by-application breakdown.

How Do the Service Temperature Limits Compare?

The two grades share essentially the same temperature envelope, so temperature is rarely the deciding factor between them: about minus 46 °C as the practical floor with impact-qualified material, and about 250 to 300 °C as the continuous-service ceiling.

Table 6. Temperature regimes for duplex stainless steels

Regime

What happens

Practical guidance

Below minus 46 °C

Toughness falls; the ferrite phase becomes the limiting phase

The normal offshore floor, and only with qualified impact tests

Minus 46 to about 100 °C

Full properties; the sweet spot for chloride duty

Seawater, desalination, umbilicals — the grades' home territory

100 to 250 °C

Proof strength declines gradually; allowable stresses fall

Re-rate from code tables; usually still attractive versus 316L

250 to 300 °C

475 °C embrittlement kinetics start to matter on long exposure

Cap continuous service unless the exposure is short and documented

400 to 540 °C

475 °C embrittlement: the ferrite hardens and toughness drops

Not suitable for continuous duty

600 to 950 °C

Sigma and chi intermetallics precipitate; corrosion resistance collapses

Avoid — also the reason PWHT is forbidden and heat input must be controlled

Which Grade Is Easier to Weld?

2205 is easier to weld: it has the wider heat-input window and the more forgiving ferrite balance. S32750 demands tighter control because its higher alloy content nucleates sigma phase faster. Both grades use the same duplex discipline, and both fail in the same way when that discipline slips — through the weld, not through the base metal.

Which Grade Is Easier to Weld.webp

Table 7. Welding parameters for duplex stainless steels

Parameter

Duplex 2205

Super duplex S32750

Filler metal

ER2209 (AWS A5.9) or E2209 electrodes (AWS A5.4)

ER2594, EN 12072 designation 25.10.4L

Heat input

Low, within the qualified WPS range

Low and tighter; biased to the lower half of the duplex band

Interpass temperature

Commonly capped at 150 °C

Commonly capped at 150 °C, often tightened to 100 °C

Root purge

Argon; 25 to 50 ppm oxygen at the vent

Argon; 25 to 50 ppm oxygen at the vent

Post-weld heat treatment

Forbidden — sigma phase forms in the 600 to 950 °C band

Forbidden — same sigma mechanism, faster kinetics

Ferrite verification

ASTM E562 point count or A799 Ferritescope; 35 to 55% target

Same methods; heavy sections often require a sacrificial test block

The consumable choice is the most expensive mistake to get wrong: welding either grade with 316L or 308L filler dilutes the weld metal and collapses its PREN, turning the joint into the weak point.

The second discipline is the quench after annealing — for 2507 the mill must transfer the section from furnace to quench tank in seconds, and the heat-treatment record (soak time, quench medium, water temperature, time from furnace to quench) is part of the quality evidence an offshore specification will ask for under NORSOK M-650. For cross-cluster welding context see the S32750 vs S32760 comparison and the nickel-alloy welding guides in the cluster.

What Heat Treatment Does Each Grade Require?

The same recipe for both grades: solution anneal at about 1040 to 1100 °C, soak roughly 30 minutes per 25 mm of section, then an immediate water quench. There is no aging, no temper and no precipitation-hardening step — the duplex structure itself carries the strength, and the anneal simply restores and locks that structure.

The quench is the entire quality-control intervention. Air cooling, or even a slow transfer through the 600 to 950 °C band, nucleates sigma and chi intermetallics within minutes — and unlike a quenched-and-tempered steel, a sigma-embrittled duplex heat cannot be corrected by a later treatment short of a full re-anneal. Acceptance is verified with ASTM A923 (Method A or C corrosion screen, Method B Charpy), ferrite content by E562 or A799, and hardness by E18. Cold work above roughly 10% strain — bending, forming, rolled threads — may warrant a re-solution anneal, a decision for the design authority rather than the shop.

How Do Sour-Service Qualifications Differ?

Both grades can be qualified for sour service under NACE MR0175 / ISO 15156-3 in the solution-annealed condition. The commonly published hardness caps are 28 HRC for 22Cr duplex (2205) and 32 HRC for super duplex (2507), and the environmental envelope — H2S partial pressure, temperature and in-situ pH — is wider for 2507, which is why it is the usual choice for high-H2S offshore and gas-processing duty.

Published hardness caps differ between editions and suppliers — some quote 28 HRC for super duplex in sour service as well. Treat 28/32 HRC as the common envelope, verify the cap against the edition named on your purchase order, and test hardness across base metal, weld and HAZ, because a hard spot in the heat-affected zone is where sulfide stress cracking starts.

What Does the S32750 Premium Actually Buy?

A 2507 order typically costs 25 to 50% more than the equivalent 2205 order, driven by the higher chromium, molybdenum and nitrogen content, the tighter heat-treatment window and lower production volumes. The premium buys corrosion margin (a higher pitting and crevice ceiling), strength (thinner wall, less weld metal) and a wider sour-service envelope — and it pays back when any of those converts into avoided repairs, avoided replacement or a lighter structure.

Table 8. Cost and value drivers (indicative, order-specific)

Driver

Duplex 2205

Super duplex S32750

Comment

Material price index (2205 = 100)

100

125 to 150

Form-, mill- and volume-dependent; quote both grades

Relative wall at equal hoop stress

0.38

0.31

About 18% thinner wall offsets part of the premium

Welding window

Wider, more forgiving

Narrower; tighter procedure control

Procedure discipline matters more than consumable cost

Failure risk in hot concentrated chloride

Higher

Lower

The premium that matters in desalination and offshore brine

Lead time and availability

Generally better

Generally tighter

Super duplex is produced in lower volumes

The lifecycle framing is simple: the cheapest correct answer is the lower grade whose envelope covers the service, and the most expensive answer is 2507 bought for strength alone — or 2205 bought where 2507's margin was needed. Compare both quotations against the wall-thickness calculation before deciding.

Which Applications Favor Each Grade?

The selection matrix below converts the property comparison into a procurement decision. The pattern is consistent: 2205 owns ambient and moderately aggressive chloride duty, 2507 owns hot, concentrated or sour chloride duty.

Which Applications Favor Each Grade.webp

Table 9. Application selection matrix

Application

Favoured grade

Why

Ambient seawater cooling and firewater

2205

Inside the 2205 envelope; lower cost and easier fabrication

Hot or concentrated brine; high-pressure desalination sections

S32750

Pitting and crevice margin at temperature

Offshore flowlines, manifolds and umbilicals

S32750

Strength, sour-service envelope and seawater margin together

Heat exchanger tubes in hot chloride brine

S32750

Crevice margin under deposits — see the S32750 heat exchanger case

Chemical process with warm, dilute chlorides

2205

Adequate margin with easier welding and forming

Sour gas (H2S) service

S32750

Wider ISO 15156-3 envelope at the same hardness discipline

Structural and architectural marine components

2205

Strength at ambient; no corrosion premium required

Continuous service above 300 °C

Neither

Step to an austenitic grade or a nickel alloy

Project-level examples from the cluster: the 84-piece S32750 butt-welding fittings shipment to Saudi Arabia, the ASTM A815 S32750 fittings order to Brazil and the UNS S32750 heat exchanger show where the super duplex grade earns its place; the ASTM A790 2205 pipe page and A182 2205 flange page cover the standard-duplex equivalents.

Use this checklist as the specification backbone for any 2205-versus-2507 purchase order. It converts the comparisons above into verifiable acceptance criteria, which is what protects the project at receipt inspection rather than at failure analysis.

How to Specify and Verify S32750 vs Duplex 2205 on a Purchase Order

  1. 1. List maximum chloride concentration, design and upset temperature, pH, flow versus stagnant zones, deposits, and H2S partial pressure if sour. This single step decides whether 2205 is sufficient or 2507 is required; every later step depends on it.

  2. 2. Calculate PREN = %Cr + 3.3×%Mo + 16×%N from the actual heat chemistry on the mill certificate. As a screening floor, treat PREN 34 as the 2205 band and PREN 41 as the 2507 band, and require the calculation from the certificate rather than from nominal composition.

  3. 3. Compare the 550 MPa yield of S32750 with the 450 MPa of 2205 against the code allowable stress, then run the wall-thickness comparison. If the pressure duty can be met by 2205 at an acceptable wall, the corrosion margin — not strength — must justify the upgrade.

  4. 4. If any part of the system can reach minus 46 °C or colder, specify Charpy V-notch testing at the minimum design temperature (commonly 45 J average, 35 J single) and confirm the grade and product form are qualified for it.

  5. 5. State the UNS number (S32750 or S31803/S32205), the product standard and form (A240 plate, A789/A790 pipe, A928 welded pipe, A276 bar, A182 forging, A815 fitting), delivery condition (solution annealed and water quenched), hardness cap, ferrite range and EN 10204 3.1 certificate type.

  6. 6. For critical duty add ASTM A923 Methods A/B/C, ferrite content by ASTM E562 or A799, and where crevice corrosion governs an ASTM G48 test at the temperature your service demands. These tests are what detect a bad solution anneal that ordinary tensile testing cannot see.

  7. 7. Match the filler to the base grade (ER2209 for 2205, ER2594 for 2507), cap heat input and interpass temperature, require argon root purge at 25 to 50 ppm oxygen, and prohibit PWHT in the procedure notes.

  8. 8. Check the MTC heat number against the material marking, run PMI on every heat, confirm hardness is within the cap, review the A923 and ferrite reports, and only then release the material to the shop. A hardness reading above the cap or a missing A923 report is grounds for rejection.

What Are the Most Common Mistakes When Switching from 2205 to S32750?

Most failures in this grade pair are not metallurgical mysteries; they are specification and procedure slips. The table below lists the mistakes that actually happen, what they cost, and how to prevent them.

Table 10. Common mistakes and how to prevent them

Mistake

Consequence

Prevention

Specifying "duplex" or "F51" without a UNS number

Wrong chemistry; nitrogen as low as 0.08% and a PREN floor near 31

Write the UNS number and product standard on the purchase order

Welding 2507 with the 2205 procedure and ER2209 filler

Diluted weld metal; the joint becomes the corrosion weak point

Re-qualify the WPS with ER2594 and tighter interpass control

Air cooling or slow quench after annealing

Sigma phase; toughness and pitting resistance collapse

Require water quench and a heat-treatment record on the certificate

Applying PWHT to relieve weld residual stress

Sigma and 475 °C embrittlement in the 600 to 950 °C band

Prohibit PWHT in the procedure; manage stress by design and low heat input

Skipping ASTM A923 because the tensile test passed

A bad solution anneal passes tensile but fails in service

Add A923 Methods A/B/C for critical duty

Buying 2507 for strength alone

A 25 to 50% premium with no corrosion benefit

Justify the upgrade from the service envelope, not the datasheet

Expecting 2507 to solve a high-temperature problem

475 °C embrittlement and sigma above 600 °C

Keep continuous service below about 250 to 300 °C

No hardness check across weld and HAZ in sour service

SSC risk at hard spots even when the base metal passes

Verify hardness on base metal, weld and HAZ against the NACE cap

Frequently Asked Questions

Q1. Is S32750 always better than Duplex 2205?

No. S32750 is better only in corrosion margin and strength; Duplex 2205 is better in weldability window, ductility, cost and availability. Upgrade only when the measured service (chloride concentration, temperature, pH, deposits or sour-gas partial pressure) falls outside the 2205 envelope.

Q2. What is the PREN of S32750 compared with Duplex 2205?

Typical mid-range PREN is about 42 to 43 for S32750 versus about 35 to 36 for S32205 (2205). Calculated from the ASTM A240 specification minima the floors are about 38 for S32750 and about 34 for 2205, which is why project specifications often require PREN of 41 or more from the actual heat chemistry.

Q3. Can I substitute S32750 for Duplex 2205 in an existing design?

Yes for corrosion purposes, but it is a procedure change, not a like-for-like swap: the welding procedure must be re-qualified with super duplex filler (ER2594), heat input and interpass control, and ferrite, hardness and impact requirements must be re-verified. Simply ordering the higher grade with the old 2205 WPS is the most common failure path.

Q4. Can I use Duplex 2205 where S32750 was specified?

Only if the full service envelope fits inside the 2205 limits: chloride concentration and temperature below its pitting and crevice margin, no sour-service requirement beyond its NACE hardness cap, and no design stress that depends on the 550 MPa yield. Substituting downward without a documented corrosion review is how premature pitting failures happen.

Q5. What is the yield and tensile strength difference?

Minimum 0.2% proof strength is 550 MPa (80 ksi) for S32750 versus 450 MPa (65 ksi) for 2205; minimum tensile is 795 MPa (116 ksi) versus 620 MPa (90 ksi). Elongation moves the other way: 15% minimum for S32750 versus 25% for 2205.

Q6. Which grade is cheaper, and by how much?

Duplex 2205 is the cheaper grade. S32750 typically carries a 25 to 50% material premium depending on product form, mill and order size, because of the higher chromium, molybdenum and nitrogen content, the tighter heat-treatment window and lower production volumes. The premium can pay back through wall down-gauging and avoided corrosion failures, but not if 2205 already covers the service.

Q7. Do both grades work in seawater service?

Yes. Both are standard seawater alloys; S32750 is preferred for hot, concentrated or stagnant seawater, brine heaters and high-pressure desalination sections, while 2205 is fully adequate for ambient seawater cooling, firewater and splash-zone duties. See the JN Alloy guide on choosing an alloy for seawater piping for the application-by-application breakdown.

Q8. What filler metal should be used for each grade?

Duplex 2205 is welded with ER2209 wire (AWS A5.9) or E2209 electrodes (AWS A5.4). S32750 is welded with a matching super duplex filler, normally ER2594 (EN 12072 designation 25.10.4L). Never weld either grade with 316L or 308L filler: the dilution collapses the weld-metal PREN and the joint becomes the weak point.

Q9. Is post-weld heat treatment (PWHT) required for duplex grades?

No. PWHT is forbidden for both grades. The 600 to 950 °C band that would relieve residual stress is the same band that precipitates sigma and chi intermetallics, which destroy toughness and corrosion resistance. Residual stress is managed through low heat input, low restraint and controlled interpass temperature instead.

Q10. What is the maximum service temperature for S32750 and 2205?

Continuous service is normally capped at about 250 to 300 °C for both grades. Above that, 475 °C (885 °F) embrittlement kinetics and sigma-phase precipitation reduce toughness and corrosion resistance; neither grade is a high-temperature alloy. For sustained duty above 300 °C step to an austenitic grade or a nickel alloy.

Q11. What is the minimum service temperature?

About minus 46 °C is the normal offshore floor, and only with impact-qualified material. Below that, the ferrite phase undergoes a ductile-to-brittle transition and toughness falls quickly; project specifications such as NORSOK commonly require Charpy testing at minus 46 °C with 45 J average and 35 J single minimum.

Q12. Which tests verify that duplex material is correctly processed?

The core set is ASTM A923 (Method A or C corrosion screening for detrimental intermetallic phase, Method B Charpy), ferrite content by ASTM E562 point count or A799 magnetic induction, hardness by ASTM E18, tensile by ASTM A370 or E8, and pitting/crevice testing by ASTM G48 when the order calls for it.

Q13. What hardness limits apply in sour service?

Both grades can be qualified under NACE MR0175 / ISO 15156-3 in the solution-annealed condition. Commonly published caps are 28 HRC for 22Cr duplex (2205) and 32 HRC for super duplex (2507); some editions and suppliers quote 28 HRC for super duplex as well. Confirm the cap against the edition named on your purchase order and verify hardness across base metal, weld and HAZ.

Q14. How much thinner wall can S32750 use compared with 2205?

At equal hoop stress the relative wall factor is about 0.31 for S32750 versus about 0.38 for 2205 and 1.00 for 316L, so 2507 allows roughly 18% thinner wall than 2205 for the same pressure duty. The elastic modulus is not higher (about 196 to 200 GPa), so deflection and buckling checks do not improve with the stronger grade.

Q15. What is the difference between S31803 and S32205?

They are two chemistries of the same 22Cr duplex family. S31803 (the older designation) allows Cr 21.0 to 23.0, Mo 2.5 to 3.5 and N 0.08 to 0.20; S32205 tightens these to Cr 22.0 to 23.0, Mo 3.0 to 3.5 and N 0.14 to 0.20. Because nitrogen drives PREN, S32205 guarantees a higher pitting-resistance floor, and most mills ship material dual-certified to both.

Q16. What do F51, F53 and F60 mean on a forging certificate?

They are ASTM A182 forging grades: F51 is UNS S31803 (2205), F60 is UNS S32205 (the tightened 2205 chemistry), and F53 is UNS S32750 (2507 super duplex). A certificate marked F60 therefore covers 2205, not super duplex; a certificate marked F53 is the super duplex grade.

Q17. Is S32750 harder to weld than 2205?

It has a narrower processing window, not a harder process. Both need low heat input, controlled interpass temperature (commonly capped at 150 °C, often tightened to 100 °C for super duplex), argon root purge at 25 to 50 ppm oxygen and no PWHT. What changes for 2507 is that sigma phase nucleates faster, so quench delay after annealing and interpass excursions are less forgiving.

Q18. When should I step up from S32750 to S32760 or a nickel alloy?

Step up when the environment leaves the 2507 envelope: H2S partial pressure or elemental sulfur beyond its sour-service listing, chloride concentration with temperature beyond its crevice margin, or strong reducing-acid duty. S32760 adds copper and tungsten for acid resistance; nickel alloys such as Inconel 625 cover the most aggressive sour and acid combinations.

For extreme operating conditions, choose JINIE; for high-end manufacturing, rely on JINIE.
A one-stop solution for:
Difficulties in material selection, processing, inspection, and after-sales support.
Tel: +86 19339900211
Add: Shuangchuang Building, High-tech Industrial Development Zone, Lu'an City, Anhui Province, China
Copyright © ANHUI JINIE SPECIAL ALLOY CO.,LTD. All Rights Reserved.